Slimelite BBS

Another Newman Like Device?

Back to AMIGA_VIDEO

From Gary Depietro · 1996-04-03 10:59 · #76679 in AMIGA_VIDEO

Area:
Home Electronics and Appliances Discussions ??????????????????????????
Msg#: 214                                          Date: 30 Mar 96  10:46:20
From: Bill Wolff                                   Read: Yes    Replied: No
  To: All                                          Mark:
Subj: Another Newman? Edwin Gray's EMA-4 Engine           [2 of 4]
????????????????????????????????????????????????????????????????????????????


                    LIGHTING AND "ENERGY SPIKES"

      Gray describes the operation of his EMA motor as "similar to
 re-creating lightning."   He says the engineering and scientific
 world has known this re-creation is possible but hasn't known how
 to do it.   "When lightning hits the ground, causing a 10-million-
 volt buildup, where does energy come from to make it from a static
 charge to a lethal charge?    Nobody really knows."

      Richard B. Hackenberger, Sr., vice-president in engineering
 for EvGray, explains how the EMA motor system operates.   "Power
 from the high-voltage section," says Hackenberger, "is put through
 a system of electrical circuitry to produce a series of high-
 voltage `energy spikes.'   The spikes are transferred to a small
 control unit, which in turn operates the major motor unit.

      The control unit, acting in a manner similar to that of a
 distributor in an internal combustion engine, regulates the
 spikes, determines their polarity (whether they be north or south)
 and directs their power to selected electro-magnets in the main
 unit.

          While this occurs, the recycle/regeneration system is
 recharging the batteries with 60 to 120-amp pulses.    The
 electro-magnets are located on both the rotor and stator of the
 large motor.  Attraction and repulsion between the two sets of
 magnets causes the motor to operate and generate horsepower.

      Once in motion, the motor recharges the batteries as a result
 of the recycle/regeneration system.   To prevent condensation in
 the main cylinder, a half-pound of air pressure has to be
 maintained.  Air is routed through the programmer for functional
 purposes. When the ambient temperature is 90 degrees, the motor
 operates at 170 degrees."

      In short, the principle of the engine is to create
 electricity and recycle energy by the factor that every time
 magnets are energized off the peak of transients, a charge goes
 back into the battery.

      It's not a constant charge, but a pulse charge of 60 amps or
 better; thus, the battery must be of high quality.   The batteries
 for the EMA motor are furnished by McCulloch Electronic
 Corporation of Los Angeles.

      After extensive research and testing, EvGray chose the model
 110-75 Energy Center, which is said to produce maximum power for
 its weight and volume over an exceptionally long life span.  This
 is achieved partly by use of an ultra-lightweight plastic case
 that minimizes dead weight (energy-storing components comprise
 more than 90 percent of the battery's weight).

      Features of the battery include extra-large plates separated
 by indestructible glass-rubber separators and a specially
 formulated lead oxide composition.   Two of the 6-volt batteries
 are used for operation, while the other two serve as a reservoir.

      Mallory Electric Corporation of Carson City, Nevada, has also
 made a major contribution toward the design of the electronic
 pulsing system.

                       LONG-RANGE AND POWERFUL

      Electric-powered vehicles are not new, of course, but the
 poor energy-storage factor of batteries and their heavy, large
 size have thus far made them impractical for use in any vehicles
 requiring a long-range capacity.

      This drawback has restricted the market for electric power to
 small limited performance vehicles.  The maximum range of these
 vehicles when driven at 40 miles per hour has been approximately
 150 miles. Range is affected by the number of stops and starts,
 grades traversed, and acceleration demands.

      The EMA motor needs only to run at 500 rpm for the normal
 recharging system to work.   In fact, it recharging capabilities
 are such that the EvGray's next version of the engine won't have
 an alternator or air pump.  The air pump will be replaced by
 blades on the rotor.

      "The idea of a self-sustaining electric motor," says Gray,
 "at first appears to go against much of the theory of electricity
 and conservation of energy.   The EMA motor does not, however,
 violate the basic laws of physics, but rather utilizes them in a
 unique integration in a system in order to maximize upon the
 characteristics and interrelationships between electrical,
 magnetic, and physical components.   The EMA prototype motor has
 had considerable operating test time and has been adapted to
 standard and automatic automobile transmissions."

      Dynamometer tests have recorded the rpm's of EvGray's motor
 at 2550 constant, the torque at 66 pounds constant.   Brake
 horsepower is 32.5 After a test run of 21 1/2 minutes, the battery
 voltage reading was 25.7.

      Only three surfaces make physical contact with the motor a
 feature which dramatically limits friction and increases
 efficiency.   "An internal combustion engine is only 30 percent
 efficient," says Gray.  "Our engine is 90 percent efficient." A
 prime factor in friction control is the so-called "magnetic
 vacuum," created in the drum, which literally takes the pressure
 off of end bearings and allows the rotor to float within the drum.

      "Our motor creates power surges-one behind the other-in
 microseconds," says Gray.   "By doing this, we are able to direct
 the magnetic flux field.   The magnetic flux is a coolant source,
 so we need no cooling system."

      Gray says the engine is not affected by rain, heat, cold any
 other type of inclement weather, or by driving through tunnels.
 "All this motor needs is oxygen.   The only external magnetic
 effect is that another field system cannot operate within this
 same battery system. The magnetic field orientation is 360 degrees
 in all directions."

      The new EMA prototype will weigh about 320 pounds, less than
 most present internal combustion engines.   It will measure 12
 inches in diameter, 18 inches in length.   (Size is linear to
 horsepower required.)   According to Gray, further research should
 make it possible to possible to reduce the size and weight through
 the use of lighter metals and more sophisticated circuitry.

      Gray says most of the motor's components can be built in a
 machine shop with a mill and lathe.   The exceptions are the drum
 itself, the electro-magnets, and a few miscellaneous items bought
 over the counter in an auto supply store.   The company plans to
 enter into worldwide licensing agreements to manufacture the
 motor.

      The safety features of the EMA are impressive.   There's no
 fan, no exposed high-voltage component parts, no exhaust fumes, no
 fuel tanks to explode, and no water reservoirs to clog up, freeze
 or overheat.

      EvGray believes the reliability of the engine will be
 excellent, and maintenance should be the engine will be excellent,
 and maintenance should be minimal because there's no carbon, water
 varnish or other impurities - which occur normally as a result of
 burning oil or gasoline - to damage parts.   There is no
 carburetor to clean and adjust, no oil filter to change, no gas
 filter, smog valve, gaskets, radiator, water pump ot timing chain.
 Plug-in type construction makes replacing parts quick and easy.

 Gray says the training time for EMA mechanics is less than that
 for mechanics working with a standard electric motor and far less
 than that for those preparing to work on internal combustion
 engines.

      The EMA also favors the eardrums of mankind. Its noise
 emission is far less than that of all other power sources, and
 Gray claims there will be no increase in noise as the engine ages.
 In fact, electric-motor noise is almost imperceptible when
 properly suppressed.

      Perhaps the reason Edwin Gray, now 48, has been able to
 create such an unconventional engine is his unconventional
 education. One of 14 children, he began tinkering with magnets and
 electricity as a boy.   He left home when he was 15 and served a
 year in the U.S. Army before it was discovered he was under age
 and he was given an honorable discharge.  During that year, he
 attended an Army school for advanced engineering. After the attack
 on Pearl Harbor, he reenlisted, this time entering the Navy. After
 serving three years of combat duty in the Pacific zone, he
 returned to civilian life and found work in the field of
 mechanics. Resuming his experiments with electro-magnetic power,
 he seriously examined the theory of energy used is energy spent.

      After years of research an experimentation, Gray conducted
 his first test of the EMA motor in 1961.   The engine ran briefly
 and then broke down.   Discouraged but not defeated, he
 constructed a second electro-magnetic motor, which ran for an hour
 and a half before failing.

      A third prototype ran for 32 days attached to various
 automotive transmissions and test equipment.   It was then
 dismantled for analysis, and detailed reports were prepared.
 After rejection by large corporations and money promoters, Gray
 formed a limited partnership in 1971 and constructed the fourth
 EMA prototype.

      With assistance from nearly 200 private citizens, EvGray
 Enterprises has spent $1.1-million in the attempt to recycle
 present lost energy and redirect magnetic forces with the EMA
 motor.

      Dick Hackenberger, who comes from a more conventional
 background, compliments Gray's raw genius with 25 years of
 diversified functional and management experience in the
 engineering field.   He holds an EE degree from Northeastern
 University and is a senior engineer in the Institute of Electrical
 and Electronic Engineers.   Hackenberger has held positions with
 the Sony Corporation of America and Sylvania Commercial
 Electronics, and he has served as an engineering consultant to the
 U.S. Navy.

      Other EvGray officials include Arthur M. Lange, vice-
 president in charge of public relations, and George C.  Demos,
 vice-president in charge marketing.   Lange has served in
 management and public relations capacities with both Ford and
 General Motors, while Demos has worded as division general manager
 for Control Data, director of marketing for RCA, and president of
 his own manufacturing firm.

                       RAISING A FEW EYEBROWS

      The electro-magnetic motor has attracted attention from
 important government agencies, including the Environmental
 Protection Agency, the Air Resources Board, and the Department of
 Transportation.   Governor Ronald Reagan of California last year
 presented Gray and his wife, Evelyn, with a certificate of merit.
 Others indicating interest in the project are congressmen Barry
 Goldwater, Jr., Edward R.  Roybal, Del Clawson and James C.
 Corman, U.S. Senator Alan Cranston, and state senators Alfred E.
 Alquist and Nicholas C. Petris.

      John Brogan, head of the Environmental Protection Agency's
 advanced automotive power systems development division, says his
 25-man staff has looked at approximately 20 alternate engine
 proposals each week for the past two years.

      He says nearly half of the proposals are of "perpetual
 motion" machines; that is, machinery that would produce continuous
 movement without any outside energy source. The concept of
 perpetual motion violates all known laws of thermodynamics.

      According to EvGray, some experts believe the EMA is a
 perpetual-motion engine and is, therefore, invalid.   Gray himself
 refutes this belief.   "The EMA motor is definitely not perpetual
 motion," he insists.   "Only those in the scientific world who
 understand the theories of physics are able to comprehend how our
 motor works. There's only a handful of such persons.

      "The programmer directs which magnets are to be energized for
 what length of time and in what polarity.   There are several
 attractions and repulsions taking place at the same time."

      The search for the clean engine has seen the federal
 government contribute $23-million to the development of new
 engines in the past two years.   General Motors, spent $36-million
 last year alone, and Ford laid out $20-million.  Senator John V.
 Tunney of California has proposed legislation to divert $900-
 million from the Highway Trust Fund into a three-year crash
 program to develop a clean engine.

      Meanwhile, Edwin Gray, after 12 years of research and
 development, believes he has found the answer for a comparatively
 meager $1.1-million.   Time will tell whether or not he is right.

                  EMA-4 MOTOR PRELIMINARY TEST DATA

 Input Power         12 volts dc (of a 24 volt dc system, making
                     use of a 12 volt standard starter motor).

 RPM                 2550 RPM constant.

 Torque              66 lbs. / constant.

 Horsepower          100 HP

 Brake Horsepower    32.05

 Foot-pounds/minute  1.057.650

 Foot-pounds/second  755 lbs. (includes 110 lbs for four 6-volt
                     batteries).

 Volume              42" long x 18" wide x 22" high. (This is
                     overall geometry. including control unit, etc.
                     - The basic motor is a 16" dia. x 24"
                     cylinder, which can be repackaged into a 9"
                     dia. x 12" cylinder).

 Test Run Time       21.5 minutes.

 Battery Voltage     25.7 volts.
 Reading at test
 completion

 Ambient Temperature 84 degrees constant.

 Humidity            51%

 Fuel Consumption    None (other than air).

 Cooling             Conduction / 1/2 pound (flow through) air
                     pressure.

 Magnetic Field      360 degrees-all directions during motor
 Orientation         operation.

 Lubrication         High temperature bearing grease (2 bearings).

 Vibration           Negligible

 Noise Level         No direct reading taken - without shielding,
                     no louder than small kitchen appliance,  e.g.,
                     fan, etc.

 Power Hazard        Fully secure - full design safety features.
 Start Mode          Simple push button - standard 12V starter
                     motor.

 Operating Mode      Rheostat principle with switchable RPM
                     range(500-1300-1950-2550-3350-4100 RPM's)

 Physical Condition  Motor mounted on wheeled test stand - no
                     external connections to stand.

                               Page 7
                  EMA - 4 MOTOR BLOCK DIAGRAM

                                                    x
                            Mechanical Conversion    
                               of Power-Drive        
                           Shaft-Transmission, etc.  <   x
                         ?                          
    
                                                          
                                                          
         x                  x                x           ! x
   24 V         High Voltage                        Motor-  
  Power       >% Generator     >%Control Unit     >%Rotor/  
  Supply  < x     Circuits                        >%Stator  
 ?       
    ?            
  ?            
    ?   ,  ,

            
                                             
                                               !   x       
     <                               Regeneration-         
                                  %  Recycle Unit          
          Electronic Pulsators (C)                         
         ?                        !                
      
                                                       
  
     
UUUUUUUUUU*        
UUUUUUUUU*    
    ?                Alternator  <     
    Air Pump   < 

                        (B)                     (A)    
                   ;UUUUUUUUUUU:           ;UUUUUUUUUU:

 BLOCK DIAGRAM OF THE EMA-4 shows how energy is transmitted from
 the four 6-volt batteries (power supply) to the various stages of
 the engine and returned.

 Both the air pump (A) and the alternator (B) are optional
 equipment. The air pump prevents condensation around the drum and
 provides added assurance of air in some environments.

 The alternator is not needed for most applications, including use
 in vehicles, but may be desirable in heavy generator rigs.


 The electric pulsators (C), which are contained in the
 regeneration-recycle unit, are capable of pulsing at 200,000 times
 per minute, and the pulsation at 60-to-120 amps is fed back to the
 batteries.

 ----------------------------------------------------------------------------
 Free Energy Page

!- PPoint 2.00
! Origin: The WIN95/GEOS Connection Point (1:115/769.2)











































... "Yield to temptation, it may not pass your way again." - L. Long
--- Proboard/Fastecho/InterMail
 * Origin: The P.I.T.S. BBS = Orange City, Fl = 6 Nodes = 904-774-6577 (1:3618/12)