Slimelite BBS

Groovey

Back to AMIGA_VIDEO

From Buzz Lange · 1996-04-04 07:55 · #76660 in AMIGA_VIDEO

RF>KS> DC> Which reminds me...  }:-)  I may have asked it here before, but
  >  > DC> just how many grooves are there on those old 33 1/3 RPM records?
  >  > DC> They were about 10 inches in diameter, if I remember them correctly.
 
RF>KS>      Damn!  I was just about finished counting them!  8*)
 
RF>    Be smart.  Count the number in one inch, then extrapolate!
 
  Well, I dunno about that.  I remember reading about a Scully lathe
  that would pre read the master tape and widen the groove spacing to
  accommodate the larger excursion for loud passages.  RIAA (I think)
  set a standard for boosting the highs above the static and cutting the
  lows to keep from plowing into the adjacent grooves.  The reverse was
  applied on playback.  EUR was another standard.
 
  Each side of the "V" shaped groove was dedicated to a channel, and to
  keep the compatibility with compliant monaural systems (with looser
  needles), one channel was out of phase.  That way, a monaural or
  balanced tone in both channels made the groove move side to side as if
  it were recorded monaural.  Out of phase sound appeared to be cut
  vertically--just like the original Edison machine cut into cylinders.
 
  Not to mention elliptical needles with point-forward angles and
  contact along the walls as two lines instead of points to track more
  in the path that the original lathe blade made.  The spherical needles
  made an error contacting the walls when the groove moved sideways.
  The best tone arms had a parallel arm to guarantee a perpendicular
  track.  B & O even produced armless tracking systems where the head
  moved on rails.
 
  The tracking pressure, although in grams, was enough to melt the wall
  where the needle passed.  Any debris would be welded in place and
  enjoyed forever there after as a pop.  I used to wash the vinyl and
  use a static (electricity) discharging dustcloth prior to playing.
  There even was some alpha source gizmo that killed the charge as the
  needle dragged along.  Tone arm brushes screwed up the tracking
  dynamics and usually weren't used by the purists.
 
  The 33s themselves did not set the dynamic limit--it was the master
  that dictated the headroom.  I remember getting albums cut with direct
  mastering from 35mm full coat.  That's the stuff they used to edit
  movie sound--it would match the picture frame by frame and was edited
  the same way, by physically splicing it.  The 35mm full coat was run
  at a rediculously fast speed (I can't remember what it was, maybe
  greater than 20"/sec) and had very wide heads.  The the thickness of
  the film base prevented a magnetic print through (when you can hear a
  loud passage coming), and the dynamic range seemed close to what we
  expect from a CD now.  Hiss was zero because the heads were so wide.
 
  There were even a few albums made with "direct to disk mastering".  No
  intermediate steps whatsoever.  The lathe operator had to preset and
  guess the dynamics of the upcoming passage.  The grooves usually were
  very far apart in these albums.  The presence was frightening--you
  could hear the musicians breathe.
 
  All this in those littlle wiggly lines on those ancient 33's.
 
  Sound from Stone-Age stuff.
 
Cheers,
Buzz.
***
 þ OLX 2.2 þ Cement Truck Hits Paddy Wagon--Hardened Criminals Escape!

--- TriToss (tm) 1.03 - (Unregistered)
 * Origin: midnight:east | zz.com | Fort Lauderdale FL USA (1:369/10)