Slimelite BBS

Batteries

Back to AMIGA_VIDEO

From Ron Freimuth · 1996-04-03 08:51 · #76654 in AMIGA_VIDEO

KS> RF> In fact, I'm running tests on alkaline cells right now.  I have
  > RF> found that some old D cells I couldn't recharge did rejuvenate when I
  > RF> put a couple of Amps, AC through them.  My tests are continuing -
  > RF> I'll report on more when I have a better idea of how useful this is.

KS>        Did you give them a reverse current jolt first?
  >        Don't forget to wear a safety shield on your
  >        face.

KS> RF> BTW, putting AC and DC through a cell to recharge it is nothing
  > RF> new. I'm just trying my own experiments.

KS>        I'd be interested in your results.

    Here are a lot of them. Looks like I'm about done.  It's hard to say
 how much I helped the batteries.  I know the 'rechargeable' alkaline
 cells I couldn't charge in the past are now good enough to put in my
 flashlight.  I won't know how long they last until the bulb dims.

    Here is a schematic of what I set up:

    | 0-120vac |  I have a variac which supplies 0-135 VAC
    |          |  to control primary voltage
    )()()()()()(
    ------------              1N4004, etc.
     )()()(         50 ohms
     |    |--------/\/\/\/-->|------|
    ///         |      +        |---|
      0-12vac   |----)|---------|  ----   1.5 - 3.0 V C/D cells
                    330 micro Fd  ------
                    Xc = 6 ohms     |
                                   ///

    The trick was to place a large electrolytic capacitor between the
 secondary of the transformer and the battery of cells. Needed to block
 the DC (get the polarity right!).  Without the resistor and diode
 connected, a significant AC current flows through the battery.  An
 ampere or more in this case.  The capacitor can get hot (I think I
 burned it out<g>).

    If the secondary voltage were set to 6 vac, about 6V/6ohm = 1 Aac
 would flow.  The AC voltage across the battery is an indication of its
 dynamic resistance.  It might be about 1/4 ohm for a D cell.

    I ran the setup for a couple of hours, just running AC though some
 alkaline cells.  That alone seemed to help them.

    Latter, I added the resistor and diode to give some DC charging
 current.  One should watch the battery voltage an not let it get above
 about 1.65 VDC per cell.  The current shouldn't be too high, that means
 setting the charge to bring up the initial battery voltage by maybe
 10%. 1.40 VDC -> 1.54 to start.

    Overcharging will weaken non-rechargable cells.

    For a 9V transistor battery, I used 1000 ohms, 10 micro Fd, and
 could set the transformer voltage over 25 VAC.  I saw about 0.3 VAC
 across the battery when 0.1 Aac was flowing, showing its resistance to
 be 0.3/0.1 = 3 ohms.

    I just picked some usable value components out of my junk box.  Not
 necessarly optimum.

    I charged several old 9V batteries at up to 10.1 VDC.  Some
 responded better than others.

    I noted that a good amount of AC current through a battery have very
 little effect on the DC voltage.  But, it seemed to rejuvenate them a
 bit, anyway.  A combination of AC and DC will rejuvenate and charge.

    I should do this is to my auto battery.  Might rejuvenate the plates.

---
 * OLX 2.1 TD *  Power corrupts. Absolute power is great!
--- FidoPCB v1.5 beta-'j'
 * Origin: Lunatic Fringe * Richardson,TX * 214-235-5288 * (1:124/2113)