From PainKiller · 1996-04-14 06:42 · #63510 in AMIGA_INT
Review of Apollo A620 Accellerator.
Written by Simon Archer on 13/4/1996
====================================
Whilst at the World of Amiga Show at the Novotel in Hammersmith,
London W14, I had the opportunity to buy the above hardware.
Being sceptical to start with, I couldn't wait to get home and
try it out.
First impressions of the kit was overall satisfactory, although
the fitting instructions were a little brief. Having said that,
actually fitting it didn't pose too much of a problem.
The only tools required were: a Phillips (PoziDrive (TM)) screwdriver,
and a bit of care.
I opened up the case of the A600 to reveal the motherboard. On my
machine, the metal sheilding had been removed on a prior occasion, but
this would need to have been removed. Next, the hard drive had to be
unplugged, but on a floppy based machine this part would be skipped.
The instruction sheet said that I had to separate the hard drive from
it's mounting bracket, and this could be put to one side as it wouldn't
be required any more. So far so good!
The Apollo A620 is designed to sit on top of the surface mounted 68000
processor, and it was this that made me sceptical about the idea. The manual
said that the socket should be lined up to fit on top of the 68000 and a
good hard push should locate it fully. A click should be heard once it was
home, although I couldn't get it to, despite pushing very hard. Another
point to note here is that on the underside of the A620 was 2 sets of 3
stick on feet, similar to that found on the underside of cases etc, of which
1 needed to be removed in order to get the card to sit in line with the
motherboard. The card was in at a rather disturbing angle which this
modification cured. It was also a rather tight fit because of the close
proximity of the floppy drive power cable plug, but a bit of care gets it in.
The hard drive was next to be fitted back in, and it was this that proved
to be the worst bit. As previously mentioned, the hard disk was removed from
it's mounting plate. The reason being that the A620 effectively takes it's
place, and in order that the drive doesn't float about, a piece of
'Velcro' (TM) is supplied in the kit which has to be stuck to the underside
of the disk in order that it be fixed down to the A620.
OK, power it up, and all is well. Right, put it all back together, and this
was the big let down. Up until now, the card seemed to have been rather well
thought out, but after fitting the keyboard etc back in, trying to get the
cases back together turned out to be quite a fight. In the end I had to try
and get the hard drive to sit as far back to the rear as possible in order
that the cases would once again meet. Finally, resolving myself to the fact
that they just wouldn't go, I decided to put the scews back in. I then
physically pushed the cases together until they 'snapped' back. The cases
now fit together, but they are under quite a lot of strain trying to force
themselves apart again.
Next was the benchmark tests. The software used was SysInfo 3.22, as I felt
this would give me a good speed comparison against my other machine. Anyhow,
here are the results:
SysInfo V3.22 by Nic Wilson
---------------------------
CopyBack Mode................................ N/A
Instruction Cache............................ ON
Instruction Burst............................ N/A
Data Cache................................... N/A
Data Burst................................... N/A
Central Processing Unit Type................. 68EC020
Memory Management Unit Type.................. N/A
Floating Point Unit Type..................... 68882
Vector Base Register (VBR) Address........... $00000000
Ramsey Chip Revision (A3000)................. N/A
Gary Chip Revision (A3000)................... N/A
DMA/Gfx Chip................................. ECS AGNUS - 2Meg
Display Mode................................. PAL
Display Chip................................. ECS DENISE
VBlank Frequency in Hz....................... 50
Power Supply Frequency in Hz................. 50
Horizontal Frequency in KHz.................. 15.60
Card Slot Installed.......................... YES
Hardware Clock installed..................... CLOCK FOUND
EClockFrequency in Hz........................ 709379
SPEED COMPARISONS AGAINST KNOWN MODELS & PERIPHERALS
A500 512k or A600 with 1MB CHIP ONLY......... 7.88
B2000, A2000, A1000 or A500 with fast ram.... 5.96
A1200/14 68EC020 ICACHE 2MB CHIP ONLY........ 3.42
A2500/14 A2620 68020 card.................... 2.02
A3000/25 68030 ICACHE IBURST DCACHE NODBURST. 0.90
A4000/25 68040 ICACHE DCACHE COPYBACK........ 0.22
CPU Million Instructions per Second.......... 4.35
FPU Million Floating Operations per Second... 0.70
Speed of Chip Memory vs A600 Chip Memory..... 2.76
Dhrystones per second........................ 4170
Overall.
If you are an A600 owner looking to upgrade, then this has got to be one
of the best ways to do it. I use my A600 as a second machine, but found the
speed of the vanilla 68000 2Mb chip ram just too slow. Now having a 25Mhz
68020, 25Mhz 68882 FPU, and 4Mb fast ram, this now becomes a seriously
useable machine and is a joy to handle.
If you can get a good price on this unit, and you don't mind a bit of
fiddling to fit it, you won't go far wrong with the Apollo A620 board.
Very recommended.
Simon Archer (A chuffed A600 owner :) )
--- Spot 1.3a #1534
* Origin: Simon from DarkSide BBS (0181 771 9100) (2:254/524.28)