

             Simple Tips for Ncomm, writen by Sam Morgan
             ===========================================

So  many  times  i've seen users come onto my BBS with Ncomm and just get
really  bad transfer rates or pick non IBM mode and thus not see what the
BBS  should  really look like, I thought I would create this small doc to
give people some tips on how to get the best comms setup possable.

Most of these tips should work on other comms programs.

To  get the best from Ncomm (Any Version) here are some of the things you
need to do on a standard 8n1 setup.

Transfer/Protocal Menu.
=======================

Make  sure  you  have  Zmodem  or  an External protocal as your choice of
protocal.

I recommend the internal Ncomm protocal unless your trying something like
Hydra, otherwise theres no point really.

Transfer/Options menu.
======================

Make  sure  you  have only these three options ticked in the menu nothing
else.

ZModem Resume
  ""   AutoUL
  ""   AutoDL

Zmodem  ACK  is  not  needed  and  all  it does is slow down transfers by
acknoledging every so many bytes.

Optionaly depending on your version of Ncomm.

Create Icons
File Comments
Transfer Bar

Can also be ticked but wont make much (If any) difference to your
DL/UL speed.

Comms/Handshaking menu
======================

If your modem is 2400 bps or higher then make sure you have RTC/CTS
ticked, otherwise Xon/Xoff for below 2400 baud.

Comms/Baud Rate menu
====================

Basicly the Higher the better.

With  a Vanilla (Non Expanded) amiga with only a 68000 Processor then you
will  probably  only  be  able  to  put the Baud rate upto 19600.  With a
Vanilla 68020 You should be able to do 38400 and possably 57600 with some
extra fast ram, faster your processor the higher the Baud rate can be.

Basicly the tip with baud rate is as long as your not getting lots of
errors then your probably alright so just see how high you can put it.

Significant speed increases can be gotten by using an updated
serial.device like artser.device, with this you may be able to increase
your serial throughput.

The  reason you want the serial speed higher than your modems acctual top
speed  is  to  take advantage of Data compression that most modems can do
nowadays.

Phone/Modem Setup Menu.
=======================

Set these Yes/No options to Yes.

Use Locked Rate

      This option simply stops the comms software setting its baud rate
      to the Connect speed returned by your modem.

Hard-DCD Checking

      The  'Hard-DCD  Checking' option switches the hardware CARRIER
      detect option on or off.  The hardware method is more reliable
      than just looking for the NO CARRIER string (if it shows up in
      a message, NComm will assume that the call has ended).

      NOTE:   Your  modem  must track TRUE CARRIER.  This means that
      the DCD signal must be "low" (off) in command state and should
      not go "high" (on) until a connection has been established.

All others set to No.

WARNING - Make sure your modem is returning the Modem to Modem connect
          speed, not the serial to Modem speed, you can tell this by
          looking when you logon somewhere and if your modem sends
          back (e.g -

CONNECT 38400/V32bis

          ) the speed you've now got set in the Comm/Baud rate
          menu then its probably sending back the Serial to Modem
          rate. Look up the command in your modem manual to change
          returned speed to Modem to Modem rate.

          SEE ALSO under DCE and DTE rate (Comms jargon for the above).

Emulation/Character Set & Screen/Custom font menu's.
====================================================

For the best Ansi Viewing set these to on.

For internal emulation of the IBM Char set then make sure Caracter Set is
set to IBM and that Custom Font is not ticked.

For  External  emulation  of  IBM Char Set (IBM font will be needed), Set
Caracter Set to ISO and Tick on the Costom font and pick an IBM font from
the requester that appears.

This should give you the best possable looking menu's on Most
(if not all) BBS's.

I recommend the HyperAnsi.Font as a Very nice clean IBM type font for use
in external emulation.

Phone/Phone Book menu.
======================

Basicly  depending  on  your  version  of Ncomm your phonebook prefs will
alter  your  default  prefs every time you phone out so you'll need to go
into  the  phone  book  prefs  for all the BBS's in your list and set the
options to those you've just set for the defaults.

Okay I think thats about it as far as Ncomm goes, if you can set that all
up then you should be left with a very nice and error free system.

All the mentioned third party extra's, Fonts, External protocals etc can 
be found on my BBS.

Yours

 (~== |\/|===== * Slime Lite BBS, +44 (0)181-230-1566, 24hr, 28.8k *
 _)AM |  |ORGAN * BarNet Landlord and Barman of the AfterHours Bar *
 ************** * BarNet HQ - 959:100/0.0 * FidoNet - 2:254/277.0  *
